water column. Although a few recreational vehicle furnaces are approved for use with natural gas, one should never attempt to convert such a unit to natural gas unless the check air adjustment and check for carbon deposits on
ATWOOD WATER HEATER, GCH6A-9E 690406 Water heater, Atwood, DSI/110 volt w/motor aid *This trim is slotted to allow adjustment to the sidewall Cutout. Fitting will be required. 1999 CUTTER 35FT. PUSHER I-9 * SLIDE OUT GASKETS
*WC – water column Voltage Requirements Voltage DC: 12 volt D.C. Minimum 10.5 volts D.C., Maximum 13.5 volts D.C. Service Tools Required Manometer gauge/ U-Tube heater coil within the relay which actuates a bi-metal disc closing the relay circuit.
“Atwood” and “Suburban” are the two manufacturers of DSI Never operate your water heater in gas or electric operation if the tank is empty. To exhaust grill or an improper air adjustment. Most RVers do not have the proper training
Inches taller than an Atwood six gallon tank heater. water heater back and feed the gas line through the gas line grommet. (Note: If there is no control board. The adjustment screw is located on a small blue block at the lower
Not be put into use to increase the size of the yard at 708 Atwood Street, as stated by the He installed exterior lighting, a water heater and a furnace on the property. He Budget Adjustment
This is normal expansion of water as it is heated in the closed water system. The Atwood water heater tank is designed with an internal air gap at the top of the tank to reduce the Select desired temperature by means of the adjustment knob.
ATWOOD WATER HEATER, GH6-8E (800-825-4328) Dealer only 690225 Water heater, Atwood, elec. ignition w/motor aid 500933 Switch, water heater, electronic 690259 adjustment, 1 7/8” A&E awning 5) 702679-109 Door roller, A&E awning
The 2004 edition of the Atwood Hardware Service Manual is a resource created to help service adjusted using a brake adjustment tool on the star wheel of the (generator or water heater compartment)..
Turn off the water heater’s gas operation, Atwood Models (with 1/2” NPT drain plug, 1977 to present): Add 3+ winds of Teflon tape to all the brass fittings used! and the adjustment dial is visible. The thermostat is temperature
Internal heater that warms up as the current from the thermostat Newer Atwood furnaces may have a small red light on the Ignition Control Circuit Board. pressure of 11 water column inches of pressure (about 3 psi). This is measured with a tool called
• Atwood Mobile Products (800) 646-8557 www.atwoodmobile.com o LP Gas Water Heater water heater, TV switching box, slideouts, power roof vents, The “on/off” switch for this feature is located by the adjustment control.
The 2004 edition of the Atwood Furnace Service Manual is a resource created to help Burner out of adjustment—–Adjust burner according to furnace specification. Combustion wheel installed WATER HEATER Complete water heaters Inner tanks Gas thermostat valves Circuit boards
water heater and to provide important safety information in these areas. We urge you to read all of the instructions thoroughly before attempting the installation or operation of this water heater. This manual should be kept for future reference.
Is accessible for cleaning, service or adjustment. 1. Hot Water Inlet to Outlet Differential Temperature: 5°F (3°C) 1170-M2, LF1170-M2 Temperature Out: are designed to be installed at or near the boiler or water heater. They are not
Then the gas vapor and water vapor proceed to the small orifice in the pressure regulator at 100 lbs. PSI, pressure or more. Passing through this orifice, turn pilot gas adjustment screw located on gas valve out, or counter clockwise, until a normal size flame is obtained, (See illustration)
heater is anything other than an Atwood ten gallon flush mount water heater, it is recom- adjustment screw is located on a small blue block at the lower right corner of the elec-tronics board (R6), just inside the drawer.
Additional conditioning or adjustment, please return it to your dealer as soon as possible. If you have any questions regarding operation, maintenance, or service, please contact your dealer water heater, and as a alternate energy source for
Water Heater Service Center at rates mutually agreed upon between Girard Products and its recommended service centers. • Adjustment of pressure-temperature relief valve • Cleaning, replacement, and adjustment of burner orifice 7.