Replace ballcock/fluidmaster 3. Install toilet 4. Replace p-trap 5. Replace faucet 6. Replace faucet/tub stems 7. Rebuild faucet 8. Install vanity 9. Solder copper Install gas piping to HVAC unit/water heater 21.
Bend ballcock float arm Ballcock float arm . Check all your faucets inside and outside. • Make sure your hot water heater pipes are insulated • When you need to replace your washer, choose an ENERGY STAR® model. They come
Stove, water heater. If to a heating plan t, licensed contractor required. • Toilet ballcock that is not anti-siphon. • Laundry and outside faucets (sillcocks) with threads need a backflow valve. Hose connection vacuum breaker
Premature wear/decay of faucets, shut-off valves, toilet tank ballcock valves and water heater elements. Periodic maintenance on these items should be considered routine and could be required at anytime regardless of age. 3.
ALL GAS LINES TO FURNACE, WATER HEATER, STOVE AND DRYER REQUIRE A LEVER HANDLE SHUT OFF VALVE NEAR UNIT. CAP OR PLUG ANY OPEN GAS LINES. Must have anti-siphon ballcock installed to code in all toilets. This means 1” air gap between overflow tube and inlet side of ballcock.
And frequent relief from hot water heater T&P relief valve. This protects the system from thermal expansion pressure buildup during times when reducing valve thermal expansion bypass is “WATTS® GOVERNOR 80” BALLCOCK AND RELIEF VALVE
2259A 18” Braided SS Water Heater Connector 3/4”fip x 3/4”fip 12.07 25 1063I Ballcock Step Nut Washer BC x 3/8 od x 7/16” Height .24 100 Ballcock Washer 1241D Item No. Description List Qty 1241D Basin Cock Locknut Die Cast .47 25
water heater from unnecessary relief discharge, reserving it for true emergencies •Reduces the need to use a more expensive thermal expansion tank or an auxiliary relief valve requiring a drain line •Prevents backflow from water closets, a serious
68031* 1 1/2 IPS x Ballcock x 12” Braided Stainless Steel WATER HEATER • COOKTOP • FLOOR FURNACE 1/2 O.D. (3/8 I.D.) with 1/2” MIP (3/8FIP) x 1/2” FIP Fittings 10-1220 25 12 Inch 10-1220P 10 10-1221 3 10-1222 25 18 Inch 10-1222P 10 10-1223 3
Float Ball (Ballcock Assembly) If refill valve & float are not adjusted correctly the tank may Hot Water Heater If you notice a puddle of water around the tank, it probably has a leak due to corrosion-sign to replace tank. Call a plumber.
WATER HEATER SAFETY Water heaters are as common as refrigerators and washing machines in ballcock repair/ replacement kit. Hardware storessell both approved and unapproved fill valves. Bacteria/chemicals/ add-itivespresent in a boiler system are back-
ballcock, releasing water into the tank and/or bowl. As the water in the tank is restored, the float rises and shuts off the ballcock when the tank is full. A type of water heater that heats water as it flows through a heat exchanger
ballcock threads U3362 U3370 U3482 U3486 U004 U066 U012 U057 U092 U138 U110 U139 U126 U244 U252 U272 U273 U340 U276 U281 U358 U366 U359 U706 U3712 U516 23036 23037 U3358 Water Heater Kit Contractor Kit Irrigation Contractor Kit tooLs Safe Seal Tool Disconnect Clips Disconnect Tongs fittings
Water heater connectors CTC-S-CB – One end of the ﬂ exible connector is supplied with ballcock end ﬁ tting. The other end is supplied with a plated, solid brass compression end ﬁ tting for connection to a supply stop valve.
Hot water heater will expand by almost one-half gallon. This is because when water is heated, its density decreases and its volume expands (see fig. 1). Since water is not compressible, the extra volume created by expansion must go someplace.
water heater manufacturers’ warranties become void if a Backflow Preventer is installed without a means of reliev- ily design a safer water system without extra plumbing for expansion tanks or auxiliary relief valves to alleviate
Produced by Northumbrian Water’s corporate affairs team. Ref: 11/09 heater in the loft or attic. • Check the ballcock in your loft tank and toilets to make sure they work freely. A faulty ballcock setting could