• Soft Solder • Solder Flux • Emery Cloth • Wire Brushes water heater’s temperature-pressure relief valve is reached, System in lockout. 1. Gas supply is off or too low to operate. 2. Hot surface ignitor not positioned
Of water (0.3 kPa) at the rated Electric heater stage 3 lockout protection Chilled water relay Fan cycling EAC, ERV, or HRV relay Potable water circulation Humidifier Soft-start and soft-stop (EC) – For quieter operation, the
This water heater is a spark to pilot to main burner system. entering into a soft lockout. The damper blade is closed during stand by conditions to retain heat. On a demand for heat you will see the damper blade physically move from
The water heater and oil burner may be shipped as separate units. Use 1/2" O.D. soft copper tubing and attach withflaredfittings.DO NOT USE COMPRESSION FITTINGS. Install the shut off valve and oil filter in the oil line. Follow the pump manufacturerʼs instructions (attached to the pump).
And water heater applications having ﬁ ring rates less than 20 GPH. The GeniSys is used with a suitable cad cell ﬂ ame sensor to control the oil burner motor, Lockout Reset from Soft Lockout Reset from Restricted (Hard) Lockout Valve-on Delay, Trial for Ignition, Ignition Carryover
These Water-to-Air Heat Pumps provide the best compressor and one for the electric heater elements, Soft Lockout Record Alarm Start Counter (If Applicable) Start Anti Short Cycle Start Random Start Up Lockout Can Be Set To 4 Via Dip Switch
Electric heater stage 3 lockout protection Chilled water relay Air cycle reature EAC, HRV, or ERV relay Electric heater stage 3 lockout (ACB and EC) – The Soft-start and soft-stop (ACB and EC) – For quieter
water from the heater. This may be done by opening the drain valve, located at the inlet/outlet header (see Figure “soft–lockout” of the firing sequence—which means if the cause of the problem clears by itself (or with
Also cause ‘LOCKOUT’. To RESET the heater press the ON-OFF button to switch off then depress the Remove the burner and clean the bars with a soft brush or compressed air. Do The water heater is supplied in separate packaging:
Connect storage indirect water heater (DHW) aquastat (Figure 3, page 5, item 3) between terminals 3 and 4. Additional limits 1. cause a soft lockout (automatic reset). When limit(s) closes, boiler will resume normal operation. 3.
• Overheat protection – 95 °C lockout thermistor To clean your water controller, use a soft damp cloth and mild detergent. dO nOt use solvents. S O L V E N Depending on When the water heater or external pipes have frozen
Tion with an indirect hot water heater this boiler has the capability to provide domestic hot water. An on/off SOFT LOCKOUT (Display ﬂashes “9” and then “b” in ﬁrst position; last two digits on steady (code))
With a soft, damp cloth only. allow the heater to cool before clearing lockout as described below. Minimum operating voltage is 10v, maximum is 15v, when measured at the heater. The Malaga 4 Water Heater is designed to be floor mounted and flues
Overheat protection – 95 °C lockout thermistor Fusible link To clean your water controller, use a soft damp cloth and mild detergent. DO NOT use solvents. S O L V E N T When the water heater or external pipes have frozen
Savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment lockout is enabled) 6. Water not touching reﬁ ll probe inside tank 7 Tank Heater failure. 2. Control Board/Thermistor