Elevate the furnace, water heater, to stop floodwater from entering the homes in your Recovering from and coping with flood damaged property . Title: Microsoft Word – Before During and After a Flood.doc Author: dmsomers Created Date:
Of the water heater for easy visibility of the pop-up water-leak indicator tab. 9. Measure and cut a length of copper tubing (or other approved tubing) so you can connect the end of the cold water supply line to the "IN" port of the WAGS valve.
You might not be the only one looking forward to your vacation. Theft increases during the summer months largely because vacant homes make for an easy target.
Flood Floods are one of the most common hazards in the United water heater, and electric panel • Construct barriers (levees, beams, floodwalls) to stop floodwater from entering the building. • Seal walls in basements with waterproofing compounds to avoid seepage.
Elevate the furnace, water heater, beams, floodwalls) to stop floodwater from entering the homes in your area. Seal the walls in your basement with waterproofing compounds to avoid seepage. During a Flood Driving Flood Facts
Hot water heater, which were stored in the crawlspace under his home. cabinets that can be stored upstairs before a flood. “I can’t stop the water from rising, but I can do my best to protect what I own,” he said. Cost: Northampton County, Pennsylvania Quick Facts Year:
In this manual, or have any questions, STOP, and get help from a qualified service If the water heater has been subjected to flood, fire, or physical damage, turn off power and water heater, or replacement component part(s),
Use pipe sealant or Teflon tape for NPT/water heater applications. Tip: Do not grip the plastic motor drive for leverage when tightening the fitting. Be sure the water supply line is connected to the appliance before going to the next step.
Familiarize yourself with these terms to help identify a flood hazard water heater and electric panel in your home if you live in an drains of your home. If feasible, construct barriers to stop floodwater from entering the building and seal walls in basements with waterproofing
water heater with any gas other than the one listed on STOP! Follow the “B” in the safety information above on this label. Water heaters subjected to flood conditions or anytime the gas controls, main burner or pilot have been
water does not stop flowing, Turn off the Gas to your water heater and insure that the pilot light is not casualties, fire, flood, freezing, environmental factors, water pressure spikes or other such acts of God. This warranty will be void if defects occur due to failure to observe
Patented No-Flood Water-Detection System Developed to Eliminate Risk of Catastrophic Floods in Homes and Businesses water heater – and the ensuing costs – Bob Henderson helped invent the No-Flood system. Kind Regards Bob Henderson
Ludell Water heater Lockouts terminal #10 and connect it to terminal #11. The burner will stop as soon as the wire is removed To test the DC High Shell Water(Flood): Momentarily touch a wire from ground to terminal #71.
Water heaters subjected to flood conditions or anytime the gas controls, main replacement of the entire water heater. LIGHTING INSTRUCTIONS 1. STOP! It is imperative that you read all the safety warnings before lighting the pilot. 2.
If your furnace and/or water heater has gotten wet, Prepare for the Next Flood Consider purchasing a backup or portable generator more information, or stop by the Department of Community Development or Village Hall for an ap-
In this manual, or have any questions, STOP, and get help from a qualified service technician, or the local electric utility. WARNING: If the water heater has been subjected to flood, fire, or physical damage, turn off power and water to the water heater.
water does not stop flowing, Reopen the supply valve to the hot water heater and allow the water to run until casualties, fire, flood, freezing, environmental factors, water pressure spikes or other such acts of God. This warranty will be void if defects occur due to failure to observe
Valve/angle-stop. 2) Make a clean cut in the supply tube where the FloodStop valve is to be installed. The FloodStop valve should be installed as far upstream FS 3/4-NPT Water Heater FS 3/8-C Dishwasher-Icemaker-Toilet FS 1/4-JG
Water Heater Failures by S. Carl Morello, PE, fresh water will flood from the inlet valve until it is turned off. Even a slow leak can automatically to stop the flow of additional water into the system. Install a catch pan under
• Raise your furnace, water heater, or electrical • Construct barriers, such as levees, berms, or flood walls, to stop floodwater from entering the building. • Seal walls in basements with waterproofing compounds. • During a flood or flash flood watch, be prepared to