Investigators continue to look into Holmes Drive explosion.
GAS-FIRED WATER HEATER A Spanish language version of these instructions is available by contacting the Install a shut-off valve in the cold water supply line. If this water heater is installed in a closed water supply system, such as the
A gas water heater cannot operate properly without the correct amount of air for combustion. Do not install in a confined area “off” until the water heater installation is complete. A gas line of sufficient size must be run to the water heater.
Open the shutoff valve on the gas supply line to the water heater. Use a approved water and soap solution to check the for gas leaks. Repair as required. Reassemble the front cover of the Heat Engine. Close and lock the door.
Residential Gas Water Heater TEMP. CONTROL KNOB HEATING SYSTEM OUTLET HEATING SYSTEM RETURN GAS SUPPLY COLD WATER INLET AIR INLET EXHAUST OUTLET CONDENSATE DRAIN CONNECTION E units over 150,000 BTUs require a 3/4” gas supply line.
A gas water heater cannot operate properly without the correct amount of air for combustion. Do not install in a Ensure tank is filled with water and the gas line is connected. 3. This appliance is equipped with a device which
• A readily accessible manual shut off valve in the gas supply line serving the water heater, and • A drip leg (sediment trap) ahead of the gas control valve/thermostat to help prevent dirt and foreign materials from entering the gas
ARMOR is a fully condensing commercial gas water heater. Available in eight models with inputs ranging from 150,000 to 800,000 Btu/hr, HEATER TO CENTER LINE OF FLUE 1/2" GAS CONNECTION DA F B 4" TOP VIEW Standard Features • Power Direct Venting System
Use soapy water to check for leaks on gas line, and on tubes under new gas control. Give gas leak time to leak since pressure is low. http://waterheatertimer.org/How-to-install-gas–water–heater.html Typical water heater gas valve replacement:
Main line gas pressure to the water heater for natural gas should be between a maximum of 14" w.c. (3.48 kPa) static pressure and a minimum of 3.5" w.c. (0.87 kPa) dynamic pressure for Natural Gas.
PRINTED IN U.S.A. 05/12 WP FORM NO. 101-14 Rev. 17 Water INTEGR ATED HOME COMFORT Residential Gas Professional Water Heaters INTEGRINTEGRATATED HOME COMFORED HOME COMFORT T
Gas line connections are fairly simple, but great care has to be taken to ensure that the threaded joints are well sealed. new gas valve every time the water heater is replaced – which is not a bad idea. Be generous with the pipe joint
RESIDENTIAL GAS WATER HEATER PERMIT REQUIRED: A plumbing permit is required for the replacement of an existing water heater. Bonding Bond hot and cold water lines and gas line with #6 copper wire and approved clamps. (CEC 250.4)
To a standard storage tank water heater. 4Natural gas tankless water heaters may provide higher flow rates than other models. 4There is no pilot light constantly burning gas line, size, and length can provide sufficient gas flow to the unit.
Check for gas leaks before placing water heater back in operation. LINE PRESSURE Remove Gas Control from water heater by rotating counter clockwise. DO NOT use a wrench on the Gas Control body, damage to the Gas Control may occur.
The mighty machine stretches 45 feet, weighs 44,600 pounds and is equipped with more than $300,000 in extras. At the Virginia Alcoholic Beverage Control, the vehicle is known as a "game changer," the terms an ABC official used to describe the mobile command unit unveiled at a May news conference in Richmond.
Reconnect the water line. Installing a Gas Water Heater, continued Project Guide Step Four Set the New Water Heater in Place 1. Install the water heater in an area with at least six inches of clearance around it for ventilation. Also, make sure to
A gas water heater cannot operate properly without the correct amount of air for combustion. “off” until the water heater installation is complete. A gas line of sufﬁ cient size must be run to the water heater. Consult
As the gas line for this water heater. The heater is not intended for operation at higher than 14.0" W.C. (3.49 kPa) (1/2 pound per square inch gage) supply gas pressure. exposure to higher supply pressure may cause damage to the