Or flashing Gas Control is operating normally. glass and light if necessary. Flammable Vapor Ignition Resistant Water Heaters Green LED Indicator Observe green LED indicator on Gas Control. Error flash codes are displayed with a three second pause
Energy Saver Gas Water Heater Photo is of 65T-65FB-3N — Pilot On Indication—Flashing green LED provides positive indication that pilot is on. Light Duty Energy Saver Models Meet or exceed ASHRAE 90.1b (current standard) C.E.C. Listed
Diagnostic Flash Codes A flashing red LED diagnostic code indicates that a sequence of events has forced a lockout condition and is in an external If the solid LED light returns, then replace to control. power connection to the water heater. Remove power strip or other GFI circuit.
A. Turn the pump on to circulate the pool water. this light will cycle on and off. If the Cell LED light is green, chlorine is being the unit is in the off mode. If the Cell light is flashing, it means there is a potential that the unit needs cleaning. Check the cell and clean
Red LED on or flashing at unit. Determine fault condition by noting which light is on. A blinking green STATUS light indicates that the microprocessor control, may be used when the water heater is being serviced or replaced.
Energy Saver Gas Water Heater System — Intelligent Diagnostics—An exclusive green LED light prompts the installer troubleshooting.– Pilot On Indication—Flashing green LED provides positive indication that pilot is on.
Air Conditioner Water Heater – A Product of HotSpot Energy LLC Green light is off: Unit is off. Yellow light on: Air conditioner is set on timer. Red light is flashing: Air conditioner is abnormal, please consult a technician. Press the “LOCK” button once,
If the red LED stops flashing and the green LED commences to glow or flash, the water heater has reset the fault condition and switched back to normal operation. the water heater and the green LED will commence to flash.
Gas water heater control technology and is standard Flashing green LED provides positive indication that pilot is on. •Intelligent Diagnostics – An exclusive green LED light prompts the installer during start-up and provides ten
• The far left LED light is green on the re sidential control and the remaining 5 LEDs If the water heater was factory equipped with a combustion blower or inducer (green) “Vacation” LED begins to blink (approx. 5 second
If the water heater will not operate, reset button above the light, and look for the green light on the circuit plate at the top left of the unit. through a pair of flashing lights on the circuit plate, to communicate the source of
Energy Saver Gas Water Heater — Pilot On Indication—Flashing green LED provides positive indication that pilot is on. Light Duty TTW ® 4 Ultra Low NOx Energy Saver Models 65 60,000 69 24 3 13 1 Ú 215 53 1
green hex-head screw), fasten it securely to the metal box or timer metal bracket. Make sure all twist connectors are tight. light will start flashing. Rotate the time dial clockwise at least one click, stopping at the half hour nearest to the present time.
Designed to prevent ignition of flammable vapor outside of the water heater. — Intelligent Diagnostics—An exclusive green LED light prompts the installer — Pilot On Indication—Flashing green LED provides positive indication that pilot
Heater & Green Heating Light Go Off Water Pump Timer Activates Compressor Stops Fan Runs T-Stat Relay Does Not Close Heater Does Not Activate After Delay Period Wait for Heater to Attempt to Restart The flashing numbers indicate the thermostat setting. 5.
Roof Flashing Regarding the clearance from the terminator to the air A green screw is provided in the junction box to ground the connection. Turn off all electric power to the water heater. Do not attempt to light the burner by hand.
CONTINUOUS TEMPERATURE READOUT = CURRENT WATER TEMPERATURE FLASHING TEMPERATURE READOUT = THERMOSTAT SETTING F. OPERATIONAL NOTES-2- -15- HEATER ON/OFF BUTTON: Green light on POWER button is lit when heater is turned on. 3.