Water Heater Installation Instructions and Use & Care Guide To obtain technical, warranty or service assistance during Leaking faucets 9. Wasted hot water 10. Long runs of exposed pipe 11. Hot water piping on outside wall 1. Replace thermostats 2.
FOR NON GLASS-LINED TANKS, CONSULT WATER HEATER MANUFACTURER valve on hand in case a plastic or leaking drain valve must be replaced). Attach hose and get ready to flush Schedule 80 plastic fittings and nipples is recommended.
Hot water will circulate to heater during summer unless a shut off valve is installed on the incoming heater hose. Use the nipples and clamps to connect new hoses from heater to old hoses going to engine Soapy water on nipple and hose eases
water connection nipples all 3/4" n.p.t. cold hot inlet outlet a collector return collector feed water circulator (optional for non-gravity systems) solar energy potable water suitable for collector single element water heater
Line pressure in order to prevent water from leaking out of the pipes while making the water connections to the water heater. After the pressure has been DO NOT apply heat to the nipples on top of the water heater. Sweat the tubing to the adapter before fitting the
Water heater manufactures explain in their steel nipples on cold and hot water connections and the drain A leaking connector can corrode a hole right through the top of your tank! Sediment in the bottom of your tank keeps the anode from protecting it. This build-up will also:
Drain off leaking water or water from activated T & P valve; must be plumbed to drain Heating element— 10623 Dielectric Water Heater Nipples 2 Includes: Header Sign, 2 Header Clips, 20 restocking cards (36" W x 54" H) (24" W x 54" H) 27
Where damage to property can occur in the event of the water heater leaking, the UV disinfection system must be installed over safe tray. 2” BSP Nipples 1000 83* 940002 LCS 17 – 15000-S-170 2” BSP Nipples 1300 250*
Use only brass nipples and unions and copper and brass fittings in plumbing the solar storage tank and expansion tank. The use of galvanized fittings or nipples, compressed over time and begin leaking on the water heater.
Do not apply heat to these nipples when making solder connections. Sweat a piece of tubing to for damage caused by water leaking from the water heater, pressure relief valve, or related fittings. Select a location as centralized within the piping system as possi-
water heater are the two most important factors in extending port nipples for ease of access. Use Teflon tape on all threaded fittings. After six months, tighten the connections once again. These may start leaking if not re-tightened. Turn water back on and check all connections for evidence of
The use of galvanized fittings, nipples, dielectric unions, CPVC, PVC or other plastic pipe is prohibited. leaking on the water heater. If not detected in a timely manner, a drip or leak may cause serious damage to the tank's
Replace water heater relief valve, nipples and flex lines with similar material when leaking. Repair or replacement of main valves located inside the contract holders home, repair of leaks inside walls on water pipes, Copper, CPVC, PVC,
Non-ferrous nipples only. CAUTION All steam and water supply lines should be flushed before connecting the unit. The water heater is supplied with a pressure relief noise generation or leaking piping is reason to
Leaking faucets/nipples. Locate and correct. Power surge. Inspect/replace fuse, heater elements and Leaks around heat trap Remove. Apply pipe dope and reinstall. Lightning. Inspect/replace fuse, heater elements and Check valve in water line. Install proper pressure relief valve. thermostat.
2 – FACTORY INSTALLED 3/4” NPT DI-ELECTRIC NIPPLES. Extend the life of the water heater by providing excellent corrosion . protection. 3 – HIGH QUALITY MAGNESIUM ANODE. Provides superior corrosion prevention and extended tank life. 4 – ELECTRIC ELEMENTS.