outlet. VENTING THE HEATER WITH DRAFT HOOD INSTALLED AS SHOWN IN FIG. 1 MUST BE CONNECTED TO A CHIMNEY OR GAS VENT. Allow more time for heater to re-heat. Leaking hot water pipes or fixtures. Have plumber check and repair leaks.
Warning: Do not tamper or detach the safety valve from the water heater. 1 Outlet 2 Inlet 3 Safety Valve* 4 Electronic User interface 5 Decorative Front Panel 6 Front Jacket 7 Back Jacket heater completely, repair the leaking joint and then refill the heater. Water Filling
• when water heaters start leaking. • Simple to install – just set water heater into • pan when installing. • Will not rust or corrode. • Standard side outlet hole (unless specified). • Comes with 1” male adapter, gasket and
Water heater must not be leaking. Water heaters shall be insulated to at least R10. Insulation must be mineral fiber manufactured as dryer outlet to the termination point (no more than 8 feet for “Clothes Dryer Transition Duct”).
The ¾” nipple extending from the hot outlet port of the water heater. prevent leaking under normal operating pressure. NOTE: Occasionally the water heater will have a pre-installed plastic stopper in both the Hot and Cold ports.
The most frequently used hot water outlet, or existing water heater system in retrofit installations. The heater must be installed in an area that is free of shade all year round. Hot water is not leaking from within the plumbing system. 4)
When the water heater outlet terminal is low enough to be touched accidentally, or is accessible to small children, a Do not assume the water heater is leaking until there has been enough time for the water in the tank to warm up.
Venter outlet (see Figure 6). 2. This water heater is capable of venting the flue gases the equivalent of thirty (30) feet of 3 inch pipe or eighty-five (85) Leaking hot water pipes or fixtures E) Polarity reversed F) Heater not grounded
By water leaking from the water heater, pressure relief valve, or related fittings. Select a location as centralized • Ensure that the water heater and the outlet are proper-ly grounded. Failure to properly ground the heater can
The water heater’s inlet and outlet connections contain non-metallic parts. Don’t sol-der pipe directly to these connections. Instead, solder threaded adapters to short pieces of pipe so that soldering is done a foot or so from the water
Fit the in-house end of the duct to the fan outlet of the housing (Figure6). For the purpose of avoiding any dangerous gas leaking into your bathroom, the duct must not be laid together with the vent-pipe of air-fueled water heater into the same flue. 5.
• Check for leaking pipe or dripping tap. A dripping tap at one drip per second the hot water line from the water heater. INLET/OUTLET CONNECTION On the cold water inlet connection, carefully follow the installation diagram (See Page 8 and 9).
Draw efficiency is the quantity of hot water available to the consumer before the outlet water water heater, any treatment would not be considered warranty related. LEAKING TEMPERATURE AND PRESSURE RELIEF VALVE
Water heater and water tank failures can happen at any time, or in a position where the leaking water would first appear. When the FloodMaster sensor detects leaking water, VAC wall outlet. No electrical wiring is required.
ELECTRIC WATER HEATER line pressure to prevent any water from leaking out of the pipes while making A combination sacrificial anode rod/hot water outlet nipple has been installed to extend tank life. The anode rod should be inspected
A leaking water heater would always have water on the floor and never dry up over time. TECHNICAL SERVICE DEPARTMENT cold water inlet nipple and hot water outlet nipple for standing water. Use a Q-tip, napkin, Kleenex or other absorbent material.
Warning: Do not tamper or detach the safety valve from the water heater. 1 Outlet 2 Inlet 3 Safety Valve* 4 Thermostat Knob 5 Decorative Front Panel 6 Front Jacket 7 Back Jacket heater completely, repair the leaking joint and then refill the heater. Water Filling
Connect cold water supply and hot water outlet to the heater as indicated on the front of the tank. (The tank is supplied with 1/2” NPT Female fitting) Force 10 Leaking from TCV Connection Loose Connection Tighten the collar hex nut on the TCV.
D Hot Water Outlet E Insulation F Gas Supply Piping G Manual Gas Shut-off Valve H Ground Joint Union I Drip Leg (Sediment Trap) A water heater may appear to be leaking when in fact the water is condensation. This usually happens when: a.
1) Shut off/close the water supply at the existing manual shutoff valve. 2) Remove the existing supply line from the manual shutoff valve. 3) Connect the FloodStop valve downstream of the manual shutoff valve (as close to the manual shutoff valve as possible).