Gas Tankless Water Heater High Efficient Condensing Indoor Direct Vent Models 2 Sizes to Choose From 1. Venting 3” or 2” PVC – 2 Pipe Max Vent length 38 Feet – including one 90º Elbow (using 3” pipe) High Altitude Capable Yes Low Nox Compliant Yes
The water heater vent outlet. Make sure that the rubber seals are seated properly and that heater. IMPORTANT: Support the vent pipe at every joint of pipe using vent pipe clamps, or sheet metal hangers. 11) Measure the distance from the Flange of the
Vertex power-vent gas water heater offers unprecedented levels of performance to meet the need. † 2" PVC pipe, elbows and condensate drain supplied to connect heat exchanger outlet to blower † PVC Vent Attenuation Assembly (VAA) supplied
Model that can use either Schedule 40 PVC/CPVC or Category III stainless steel pipe † Direct Electronic Ignition wall-mounted water heater(s) shall be direct/power vent Model NC199 Series as manufactured by Noritz America Corporation.
Combustion gases are vented through PVC, CPC or ABS plastic pipe. 8. Condensation formed by cooled combustion Water heater(s) shall have combined vent capabilities of up to 120’ to the exhaust outlet with up to 120’ to the air inlet.
Tankless Gas Water Heater Optional accessories (see below) Direct Vent (Indoor) 2” PVC Vent Dual Primary and Secondary Stainless Steel Heat Exchangers / / 0( () and 1/2” Gas Pipe TM Indoor and Outdoor Venting Options
EnvirosenseTM Power Vent 90% Efficient Gas Water Heater The EnvirosenseTM Power Vent is a 50-gallon, 76,000 BTU gas water heater, equipped with a fully ULC S636 PVC pipe as follows: 2˝ pipe allows vent runs up to 25 equivalent feet
VENT PIPE EXTENSIONS 7 224051 224260 10” Vent Pipe Extension 224052 224265 19.5” Vent Pipe Extension 224053 224270 39” Vent Pipe Extension 18 169044 Pipe Clamp 26 224040 Water Heater Guard (for commercial applications) 25 16 15 4 5 6 14 17
PowerVent Induced Draft Gas Water Heater with the Guardian System •PVC, ABS, or CPVC vent pipe options 90° ELBOWS NUMBER PIPE PIPE WITH VENT OF 45° LENGTH LENGTH TERMINAL ELBOWS REQ. (FT.) (FT.) One (1) None 4.0 44.0
vent water heater, snow accumulation and drifting should be considered in areas where applicable. available for vent pipe installation. Figure 5 Figure 7 Locating the New Water Heater (cont’d) 9 •0″ clearance for 3 ″ PVC,
Water heater(s) shall be of power-vent design, using 2”, 3” or 4” PVC pipe for horizontal and/or vertical vent runs. Water heater(s) shall have: 1: Seamless, glass lined steel tank construction and a spiral-shaped heat exchanger placed
9007680005 3” Concentric PVC Termination CONDENSATION DRAIN 9007994005 Drain Tee (Horizontal) 9007985005 Adjustable Vent Pipe (10”-18”) X X X 9007981005 45 Degree Elbow X X X UBROTA0911 ©2011 U.S. Craftmaster Water Heaters 500 Princeton Road Johnson City, TN 37601
Uses inexpensive PVC, CPVC or ABS pipe. Canadian installations require ULC S636 approved PVC or CPVC for venting. Water heater(s) shall be of power direct-vent design, using 2”, 3” or 4” PVC pipe for horizontal and/or vertical vent runs.
water heater installation manual. Vent or air pipe and ﬁ tting PVC schedule 40 ANSI/ASTM D1785 CSA or ULC certiﬁ ed only (ULC-S636) vent pipe passes through an unconditioned space. The condensate drain hose barb ﬁ tting and the