Connect the electric pool heater to the power outlet.Test RCD as Check water is flowing through the heater.Then turn heater on. IMPORTANT If the heater is not in an upright position a safety switch will automatically turn the heater off.
The water heater must be installed with an UL approved Category III Stainless Steel appliance vent adapter and Rheem approved vent termination. 7” Pipe 4” Pipe Horizontal Vent Installation 13. 14 Installing the water heater:
Water heater switch Space heater switch Charger switch Reverse polarity indicator Residual Current Device (RCD) Miniature Circuit Breakers (MCB’s) RCD Test button 12 Volt DC fuses (under flap) Sytem Shutdown switch LCD item select buton LCD item
Water heater switch Space heater switch Charger switch Reverse polarity indicator Residual Current Device (RCD) Miniature Circuit Breakers (MCB’s) RCD Test button 12 Volt DC fuses (under flap) Shutdown switch Battery select button Lights button Pump
Supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30mA. ensure your Pool Heater matches your pool’s water volume along with your Filter Pump’s designated water flow rate.
Only clean filtered water should enter the heater. It is essential that the pipe work connecting to and from the heater has a minimum bore (internal Power failure external to the heater. Remedy: – Check any fuses, RCD or other switch components installed in the supply cable.
Combination space / water heater appliance the water heater button is not used. * electrical systems 58 ec400 power control system Check Residual Current Device operation. Locate the RCD within the EC155PSU and ensure the RCD is switched on (lever
RCD-protection Power supply depending on combi- nation • 22 kW continuous flow heater for hot water processing Water heater: 10 Litre boiler, 2,0 kW Heating (+Thermostat): 1x 500W, 2x 250W Dimensions: LxWxH approx.: 3200 x 740 x 3015 mm
Long and trouble-free life from your water heater. Important: All plumbing connections must be completed before making the electrical connections. SPECIFICATIONS residual current device (RCD) should be installed in the circuit. This may be part of the consumer
Rheem Water Heaters 2600 GUNTER PARK DRIVE EAST – 1 – Technical Bulletin 1799 Bulletin #HDG01 July 01, 2002 To: All Rheem Water Heater Distributors Subject: Recommended Commercial Retrofit Program for RCD or RFD or RF 50-98, 98-50, 67-120, 120-67, 75-125
heater on. • Re-plug the GFCI/RCD and press the “RESET” button. • The temperature sensor will cut off exceeds the heater capacity. 3.The water temperature is too low. 1.Heating time too long. 1.Hose clamps. 2.Hose seals. 1.Product failure or electrical
heater on. • Re-plug the GFCI/RCD and press the power of heater when the water temperature is above approximately 95oF (35oC). It continues to work when the water temperature drop below approximately 82oF (28oC). • Turn on the filter pump.
Unvented pressure system water heater is manufactured to the 3.8 A residual current device (rcd), formerly known as an earth leakage circuit breaker (elcb), with a tripping current of 30mA must be incorporated in the circuit.
Clear push switch – Water heater switch, this switch turns the 230V supply to the separate water heater on or off. Residual Current Device: RCD 40A 30mA trip to BS EN 61008 Miniature Circuit Breakers: MCB’s type C 6000A breaking capacity to BSEN 60898
‘PIH’ Portable Immersion Heater The EXHEAT ‘PIH’ range of portable immersion heaters are suitable for Installation We recommend that the electrical supply is protected by an RCD and that the heater is fully earthed. The element must be fully submerged before being energised
Check that the water heater is filled with water then switch on the electrical supply to the water heater (switch on the RCD, which is located on the connection box adjacent to the water heater).
If RCD has tripped, first check that other equipment in the installation Inadequate mixing of the warm water from the heater with the cooler water in the pool, leading to a layer of warmer water forming at the height of the inlets.
The heater and water pump must be installed at the same level. The highest part of the filter pump must be at least 150mm below pool water level. corriente residual (RCD), con una corriente operativa residual que no exceda los 30mA. 16.
heater on. •Re-plug the GFCI/RCD and press the “RESET” button. •The temperature sensor will cut off the power of heater when the water temperature is above approximately 95 oF (35°C). It continues to work wh en ta rm pu do