Avoid sharp bends and 90 degree ells in the plumbing wherever possible, as they reduce water flow. Should the water heater. turn on water pressure pump. AIIow pump to run a few minutes to expel air from the lines, then shut off faucets.
The SEISCO water heater can be installed if a surrounding enclosure is constructed of 5/16 inch or greater Do not cut the shipping carton with a sharp instrument. Stand the unit upright and remove the plastic wrap. Remove the screws that hold the front
NOTICE: THIS KIT CONTAINS SHEET METAL PARTS, WHICH MAY HAVE VERY SHARP EDGES. USE LEATHER GLOVES WHEN HANDLING VENT COMPONENTS. 4-degree downward pitch. Trim Plate Installation – At-tach the trim plate to the tions to the tankless water heater, this adapter must be securely and directly
People arrested are innocent unless proven otherwise in court. Initial charges often change as a case progresses.
The water heater’s efficiency is measured as an Energy Factor (EF), which is usually listed beside the EnergyGuide label. The higher the number, the more energy efficient the water heater. A BETTER FUTURE
Open the water heater bypass and then the drain valve that goes down through wood chisel that is also quite sharp. You need something stiff and with a cutting edge—a flimsy blade won’t hack it, and even a stiff putty
Heater Craft 6672 Boekel Road Rathdrum, ID 83858 Attn: Technical Support (208) 687-4400 Fax (208) 687-9700 www.heatercraft.com. Heater Craft 2 Year Limited Warranty 2 and secured to prevent penetration from sharp objects or edges. All water hoses
water heater and leave it 25mm (1 in.) shorter than 80mm (3-1/8 in.) pipe. 3. restrain the heater. Afew sharp blows on the handle of the socket wrench will loosen the anode nut. If an impact wrench (power drive) is available, this is
water use. Avoid sharp bends and 90° ells in the plumbing wherever possible, as they reduce the water flow. Should copper fittings be desired, DO NOT apply FROM WATER HEATER (See Fig. #1) To determine the proper setting of the gate valve (4),
Water heater wraps are an effective way of improving the efficiency of older units, as well as newer units. watch out for sharp edges on the thermostat and water heater cover. • If the water heater is in the attic, wear proper footwear and make
For Solar Water Heater Market Development in the Himalayan States” was undertaken during the year 2011. thereby producing sharp shadows of any object. By contrast, diffuse radiation does not have a specific direction. The sum of
Water Heater Stand Model number: 598-011 . Tools Needed: Hammer, Phillips screwdriver, and 7/16 nut driver . Some edges may be sharp. Box Contents: Description Qty . Platform/Top 1 . Legs 18" galvanized steel 18-ga. 4 . Cross braces 2 .
Fixing points with no sharp edges. Quicker and simpler installation The QL water heater is easily mounted, vertically or horizontally. QL Water Heater 220V**) 20 liters (5.3 gal) 41103523 366 x 358 x 430 mm / 14.4×14.1×16.9” 800 W 220 V 7 kg / 16lb
During vent installation, avoid sharp turns, long horizontal runs and improper pitches. Maintain proper support of vent connectors and joints, observe clearances from all combus- of a Bock water heater installed in a conﬁned space. When com-
WATER–HEATER FOR VEHICLES Technical description Installation instructions Operating instructions Maintenance instructions Water–heater for vehicles use only a sharp knife to cut fuel hoses and pipes. Interfaces shall not be crushed and
Floor or wall, and the heater water hoses can be easily attached to the cabin heater core lines. The When installing fuel lines, use only a sharp knife to cut fuel hoses and pipes. Interfaces shall not be crushed and must be free of burrs.
Keep cord away from heat and sharp edges. Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord. water heater to prevent direct nozzle spray from coming in contact with the water heater.